tell me the most ass over backward shit you do to keep your system chugging?
here’s mine:
sway struggles with my dual monitors, when my screen powers off and back on it causes sway to crash.
system service ‘switch-to-tty1.service’

[Unit]
Description=Switch to tty1 on resume
After=suspend.target

[Service]
Type=simple
ExecStart=/usr/local/bin/switch-to-tty1.sh

[Install]
WantedBy=suspend.target

‘switch-to-tty1.service’ executes ‘/usr/local/bin/switch-to-tty1.sh’ and send user to tty1

#!/bin/bash
# Switch to tty1
chvt 1

.bashrc login from tty1 then kicks user to tty2 and logs out tty1.

if [[ "$(tty)" == "/dev/tty1" ]]; then
    chvt 2
    logout
fi

also tty2 is blocked from keyboard inputs (Alt+Ctrl+F2) so its a somewhat secure lock-screen which on sway lock-screen aren’t great.

  • eldavi@lemmy.ml
    140·
    3 months ago

    intel won’t allow its linux drivers to work above wifi 4 speeds in ap mode, so i created a kvm virtual windows machine with pci pass through on the wifi nic plus ip masquerade and now i’m getting wifi 6 speeds in ap mode.

      • eldavi@lemmy.ml
        16·
        3 months ago

        it’s horrible in more ways that you would expect and what other solutions exist with intel wifi hardware in ap mode on linux?

      • eldavi@lemmy.ml
        19·
        3 months ago

        i wasn’t aware that you could use ndiswrapper on an access point; i’ll look into it.

        UPDATE: googles says that you can’t do this because ndiswrapper uses windows drivers that don’t support ap mode.

      • eldavi@lemmy.ml
        5·
        3 months ago

        it’s a pita every time something goes wrong; it works well most of the time, but it also REALLY sucks sometimes.

    • unexposedhazard@discuss.tchncs.de
      9·
      3 months ago

      Lots of laptops just use a removable m.2 wifi card. Have you considered replacing it with something thats properly supported? I know hardware costs money but not that much probably.

      • eldavi@lemmy.ml
        12·
        3 months ago

        It’s not a laptop; it’s a mini desktop that I obtained to serve as a wifi router; storage server; firewall; VPN; media server; remote file storage; and my cat’s favorite warm napping surface.

        the wifi nic is embedded on the motherboard and it was chosen since it included a high gain antenna; among other qualities.

        Wifi works fine if you use it in ordinary client mode w full Linux support and the hardware is capable of fully supporting ap mode in older Linux kernels; it’s just that Intel decided remove higher speed ap mode support in the latest versions of the driver to force people to buy thier more expensive wifi nics.

        • eldavi@lemmy.ml
          2·
          3 months ago

          It’s not a laptop and the hardware is fully capable of ap mode support in it’s older iteration of drivers; Intel made the decision to remove that capability in the recent versions of the driver.

  • delirious_owl@discuss.online
    1053·
    3 months ago

    My control key was broken, but I found that when I used an app and held down the space bar key, the CPU would get abnormally hot.

    So I wrote an Emacs interrupt to interpret a rapid CPU rise as “press the control button”.

    Unfortunately the dev pushed an update that broke space bar heating, which broke my workflow. I opened a bug report about it, though…

  • I_like_cats@lemmy.one
    93·
    3 months ago

    My mother uses some software that runs in the browser for her shop. It can print out receipts and scan items. To do these things it has a small “sattelite” application that runs on the system and interacts with the printer and scanner. This software only runs on Windows and Linux doesn’t have drivers for the scanner.

    When I switched her over to Linux and found this out in the process I wanted to stop, give up and install windows.

    But then I had a stupid idea. I could run the sattelite program in a Windows VM and pass through the USB devices for receipt printer and scanner. The webapp uses requests to localhost:9998 to communicate with the sattelite so I set up a apache server that proxies these requests into the VM. I also prevented the VM from acessing the Interner so Windows doesn’t update and screw everything up.

    And it works. It has been in use for a week now and I’ve heard no complaints. I’m just praying to god it doesn’t break

    • capital@lemmy.world
      25·
      3 months ago

      At least getting a snapshot of the Windows VM should be simple. And since it doesn’t connect to the internet and doesn’t update, restore should be quick and relatively easy.

    • averyminya@beehaw.org
      14·
      3 months ago

      Create a script to send important data records (if you need that for taxes or inventory data etc) as a nightly routine, that way you have a consistent database for any important records.

      Then just create a restore point. If it breaks in 2 weeks, then you just relaunch it and know that it’s going to kill itself in 2 weeks. A simple restart to that restore point solves everything.

      Sounds 100% functional to me!

  • Ephera@lemmy.ml
    54·
    3 months ago

    I like to use unclutter to hide my mouse pointer after a few seconds without being moved.

    Now, the thing is, it doesn’t just visually hide the cursor, it actually removes it, so UI elements triggered by hovering disappear. Sometimes that’s great, other times it’s infurriating, like when reading a tooltip or menu.

    I mostly use a touchpad, and so I developed a habit to wiggle my finger while I’m intentionally hovering something, so that there was enough mouse movement for unclutter to not remove my pointer.

    Then I found a setting for the jitter threshold of the touchpad. Basically, with the threshold on, it ignores tiny movements, because the hardware reports finger wiggling, even if you hold your finger perfectly still. Which is perfect for me to turn off.

    Now when I have my finger on the touchpad, it automatically wiggles and allows me to read hover elements. If I take my finger off, it stops wiggling and removes the cursor.
    It’s almost like someone designed an OS with touchpads in mind, rather than them being an afterthought.

  • UNY0N@lemmy.world
    48·
    3 months ago

    This certainly isn’t of the same caliber as some of these other comments, but I found it to be fitting to the topic.

    Last year I was having problems getting the game stellaris working on arch. (I use bazzite now, btw) My solution was the following:

    1. download the game via steam.
    2. switch it to use proton
    3. switch it back to linux version
    4. use the terminal to make the entire game folder read-only, so that steam couldn’t touch the game anymore and screw it up.
    5. add the exicutable to PATH
    6. start the game via terminal

    If any one of those step was left out, it didn’t work. I’m no linux expert, so I didn’t have the skills to actuality find the real problem.

      • UNY0N@lemmy.world
        7·
        3 months ago

        Blind trial and error, mostly. Making the game folder read-only was the real “duct-tape” part, it occued to me to do that after steam kept “updating” the game and breaking my solution.

  • dosse91@lemmy.trippy.pizza
    44·
    3 months ago

    I think this one beats them all.

    My home server keeps a few services up, including an instance of Jitsi Meet. The server runs nixos and the nixos package for jitsi is incomplete to say the least and doesn’t even support authentication, so I use the docker-compose version and I have a script that runs periodically to keep it updated. So far so good, right? Well, no.

    Because the server is at home, I have a dynamic external IP address, so I have to use a DDNS provider, but jitsi doesn’t expect this and uses a stun server at startup to determine the public IP of the server once, so if my connection goes down or is restarted and the IP changes, jitsi needs to be restarted or it won’t work anymore.

    The solution?

    • My router runs OpenWrt, so I am able to run a script that checks for external IP changes. When a change is detected, it uses SSH to connect to my server to restart jitsi
    • Because I don’t want the router to just be able to run any command, I created a jitsi-restart user that has no shell
    • When the router tries to log in with its pubkey, sshd creates a file called restartasap in the jitsi folder and closes the connection
    • On the server, there’s a systemd unit running a script as the jitsi user that periodically checks for that file, and if it exists it deletes it and restarts jitsi

    I’ve been running this setup since mid 2020 and I expect this to continue until IPv6 becomes the norm.

    • Norah - She/They@lemmy.blahaj.zoneEnglish
      2·
      3 months ago

      why not just run the IP check script on the box jitsi is on? a quick google gave me this: dig +short myip.opendns.com @resolver1.opendns.com and this: wget -q -O - checkip.dyndns.org | sed -e 's/.\*Current IP Address: //' -e 's/<.\*$//'

      • dosse91@lemmy.trippy.pizza
        2·
        3 months ago

        The jitsi user is a system user so it can’t login even if you set a key for it. Besides, I wouldn’t risk it anyway since that user is in the docker group, if it gets compromised somehow, the attacker would have very high privileges.

    • deltapi@lemmy.world
      5·
      3 months ago

      I duct taped a RPi4 to the back of a Motorola Lapdock and used custom cables to make the combo into the worst laptop ever. If yours counts, mine does too. This is what the Lapdock looks like:

  • Snot Flickerman@lemmy.blahaj.zoneEnglish
    38·
    3 months ago

    I have an old laptop running some basic services.

    I have taken it apart before to replace the hard drive with an SSD, but I never replaced the dead CMOS battery because you have to literally completely disassemble it to get at the battery.

    So I have a cronjob that runs on startup to change the system clock to the right time-zone.

    It just felt simpler than completely disassembling a hard-to-take-apart laptop.

    • piexil@lemmy.world
      2·
      3 months ago

      Debian (and Ubuntu) has the package “fake-hwclock”. I’m sure other distros do too.

      Periodically saves the time info to disk and resets the clock with it on boot.

  • Random Dent@lemmy.mlEnglish
    32·
    3 months ago

    I have a folder full of scripts tied to aliases that fix various things when they go wonky, and I’ve long since forgotten what any of them do. I just know if xxx app stops working, I type fix_xxx into the terminal and then it does a bunch of stuff and then it works again lol.

    Also I have a bunch of aliases tied to common tasks, like e1 = reboot, e2 = shutdown etc. I have no idea where that habit came from.

    Edit: ALSO, just the general mish-mash of apps. I won’t have anything to do with Snaps, but the rest of it is an unholy combination of native apps, things from the AUR, flatpaks, Appimages, Docker containers and wine setups, mostly (but not all) in Bottles.

      • Random Dent@lemmy.mlEnglish
        1·
        3 months ago

        I’m not even sure what that would do! Presumably list every time the word alias appears in every file across the whole home directory or something like that?

          • Random Dent@lemmy.mlEnglish
            1·
            3 months ago

            Alright, I’m gonna try it and see how long this takes!

            edit: about 8 minutes. Not as spectacular as I’d hoped lol

            • MonkderVierte@lemmy.ml
              1·
              3 months ago

              If you have games there, yeah. Ripgrep is way faster. But grep is good enough in most cases.

              Btw, did you find your aliases?

              • Random Dent@lemmy.mlEnglish
                2·
                3 months ago

                I did! I know where they are and which scripts they point to, but as for going into the scripts and trying to remember what they’re actually doing… I’ll get to it some day lol

  • cryoistalline@lemmy.ml
    28·
    3 months ago

    I had to use unity game engine for one of my assignments for school, but unity wouldn’t generate files needed for the language server unless I set the code editor to vscode. I fixed this by creating a bash script with the path /usr/bin/code that opens neovim in konsole.

    #!/usr/bin/env bash
konsole -e "nvim $@"
  • bodaciousFern@lemmy.dbzer0.com
    25·
    3 months ago

    I’m using Gentoo with systemd and a customized kernel, and additionally I have the /usr partition LUKS encrypted. Because /usr is absolutely essential for systemd to function, I configured dracut to make a specially crafted initrd which activates the luks lvm and prompts for the password to decrypt and mount /usr on startup before systemd init tries to run.

    About a year or two ago, some update to dracut or some other dependency (assumption) caused the dracut generated initrd’s to kernel panic. After multiple days of troubleshooting, I discovered that just copying forward an older initrd in /boot and naming it to match the new kernel, e.g. initramfs-6.6.38-gentoo.img , allows the system to boot normally .

    So, my Gentoo is booting a kernel 6.6.something with a ramdisk generated in the 5.9 kernel era. I am dreading the day when this behavior breaks and I can no longer update my kernel 😳

  • slazer2au@lemmy.worldEnglish
    24·
    3 months ago

    Had a Centos VM that kept slipping time. Every week it would loose about 30min. No amount of NTP syncing got the time correct until manual intervention.
    Msp couldn’t work it out, couldn’t rebuild the server for infrastructure reasons, and only that server had the issue. The other 3 VMs on that host were fine.

    Cron job on one server took it current time, sshed to the dodgy server and configured the correct time.

  • cizra@lemm.ee
    21·
    3 months ago

    BZ2-ing up a terabyte of zeroes (back when a TB was more than people commonly had, then zipping that file up together with another file, to bypass virus scanners in emails that prevent emailing .exe files.

    I’ve also seen a self-referential .zip file somewhere that contains itself.

  • xp19375@sh.itjust.works
    211·
    3 months ago

    sssd didn’t work well with my company’s AD server, which would cause repeated authentication failures until I restarted sssd. I rigged up a bash script which would restart sssd any time xscreensaver logged an auth fail.

  • woelkchen@lemmy.world
    20·
    3 months ago

    An old (now decommissioned) notebook of mine had a broken headphone jack. I didn’t have BT headphones then. Audio output worked technically but the detection whether headphones were plugged in or not did no longer work.

    I wrote a very short amixer script to force unmute the jack, set the volume to 50 or so percent and set the speaker volume to 0% but not “mute” state. I could then use my wired headphones again.